Kent RO Service Aurad @8506096743

If your Kent RO in Aurad is giving trouble right now, it is usually a clear fault pattern, not random damage. Water Purifier Care India (WPCI) technicians typically start from what you notice at home, then check the RO stages in sequence: inlet, filters, RO membrane, storage tank, and UV/UF parts (if present). This saves time and prevents unnecessary part swapping.

What symptoms usually mean in a Kent RO (and what a technician checks first)

• Salty or bitter taste in purified water: technician checks the RO membrane performance first, then checks whether pre-filters are clogged and whether there is any bypass/leak in the product line.

• Bad smell or cloudy water: technician checks sediment pre-filter loading (especially after monsoon turbidity), then checks carbon filter saturation and whether the tank and outlet line need sanitization.

• Slow water flow / weak output: technician checks low inlet pressure from borewell or municipal line, then checks clogged sediment/carbon filters and checks the booster pump (if your model uses one).

• Water leaking from sides or under the unit: technician inspects housing seals and quick-connect joints, checks if a filter housing is cracked/loose, and verifies whether the RO membrane housing is leaking.

• Machine making continuous noise / frequent cycling: technician checks tank float/level switch, solenoid valve (SV) operation, and checks for low voltage or pressure fluctuations affecting the control board.

• No water / not filling storage tank: technician checks inlet water supply, verifies solenoid valve response, checks float valve and tank line blockage, and checks whether the purifier is getting proper power and pressure.

Inside a service visit: the exact order WPCI follows in Aurad

1. Quick confirmation at your tap: technician checks taste, flow rate, and whether the tank is filling or only dispensing.

2. Pressure and line checks: inlet pressure (borewell vs municipal), drain line flow, and whether any restriction is present.

3. Filter stage inspection: sediment pre-filter and carbon (pre-carbon and post-carbon where applicable) are checked for clogging or exhaustion; housings are checked for leaks.

4. RO membrane and rejection test: RO membrane is tested for performance; if needed, it is replaced and the system is flushed to stabilize output.

5. Tank and controls: storage tank inlet, float valve/level sensor, and any UV lamp/UF cartridge are inspected (based on your model).

6. Final functional checks: technician verifies normal cycle, checks for abnormal noise, and re-tests output quality using a TDS meter where available.

Maintenance intervals that match Aurad conditions (hard water, monsoon, tank storage)

Aurad input water quality can swing with municipal supply and monsoon. In hard-water areas, scaling hits the RO membrane faster, especially if pre-filters are overdue. A technician typically recommends service spacing like this (typical, not guaranteed for every home):

What decides the repair or service cost in Kent RO (no guessing)

• Which stage is failing: filters only, booster pump/SMPS, solenoid valve (SV), storage tank float/level sensor, or RO membrane.

• Your input water: higher TDS and hard water increase membrane scaling, which can push replacement earlier.

• Symptoms severity: slow filling and weak flow usually mean clogged stages; salty taste often points directly to membrane performance.

• Whether any parts have leakage or physical damage: cracked housings, leaking quick-connects, or damaged wiring changes the work.

• Model configuration: some Kent units include UV/UF, others rely mainly on RO + carbon; service scope changes accordingly.

• Whether you already missed previous service: overdue filters can choke the membrane and raise the chance of multiple parts needing attention.

How long the work takes, and when repairing is worth it

Most filter and cartridge services are quicker when parts are available and the fault is limited to the pre/post stages. RO membrane replacement and any control/valve issues take longer because the technician needs to test performance and flush the system after installation. Repair is usually worth it when the unit is otherwise working normally (tank fills, no major electrical failure, no repeated leaks after fixing seals). If the issue is only taste and flow due to filters, the repair is typically straightforward. If there is persistent salty water even after basic filter cleaning, the membrane is the likely root cause, and replacement often gives the best outcome.

Before you call: 6 quick checks you can do at home (safe ones)

• Check whether the tank is filling: watch whether the storage tank level rises after you switch on.

• Check whether the flow is weak only for purified water or also for inlet water.

• Smell and taste: note if it is salty, bitter, chlorine-like, or just dull/cloudy (this helps diagnosis).

• Look for visible leaks: check around filter housings, tubing joints, and under the unit.

• Listen for cycling/noise: if it keeps running without stopping, it often points to float/solenoid/pressure issues.

• If you have a TDS meter: note inlet TDS and purified TDS readings (even one set helps the technician).

If you tell the technician your exact symptom (salty, smell, slow filling, leakage, noise, or no water) and what changed recently, the diagnosis becomes faster. Next step: book a Kent RO service visit for Aurad and keep the unit running normally until the technician arrives, so they can confirm the fault pattern correctly.