Kent RO Service Aurangabad @8506096743

If your Kent RO purifier in Aurangabad is acting up right now, you usually notice it first by taste, smell, flow, noise, or water not filling. This page is for Kent RO service in Aurangabad when the RO output quality drops or the machine stops behaving normally. A technician from Water Purifier Care India (WPCI) typically starts by reading your symptoms, then checks the RO stages in the correct order so the right part gets fixed the first time.

Symptom-first diagnosis: what you notice usually points to

• Bad taste (metallic/chemical) or bad smell: often a carbon post-filter issue, or bacteria growth if the storage tank/lines are not being cleaned regularly.

• Salty taste even though RO is running: usually RO membrane exhaustion or a bypass/leak in the RO housing; also check TDS reading if available.

• Slow water flow from RO tap: common causes are choked sediment pre-filter, clogged carbon filter, low inlet pressure from borewell/municipal, or a failing booster pump.

• Machine making unusual noise (humming, vibration, clicking): can be booster pump cavitation, solenoid valve (SV) sticking, air in the line, or electrical issues in SMPS/relay.

• No water / RO not starting or not auto shut-off: often SV problem, float valve issue in the storage tank, blocked inlet, or low voltage/low inlet pressure.

• Leakage from the purifier body: usually housing seal failure, loose fittings, cracked RO membrane housing, or damaged tubing connections.

What a Kent RO technician checks in the right order (typical service flow)

• Talk with you first: confirm what changed (taste, smell, flow, noise, leakage) and whether it happened after a monsoon/municipal water change.

• Check inlet water conditions: inlet pressure, continuity, and whether the feed water is very turbid (common in Aurangabad monsoon months).

• Inspect and test filters: sediment pre-filter and carbon filters are checked for clogging, discoloration, and fit; if they are bypassing, RO quality drops.

• Check RO membrane performance: technician checks TDS rejection trend (if a meter is used), membrane pressure, and looks for signs of membrane scaling/age.

• Check control and water level parts: solenoid valve (SV), float valve in the tank, and storage tank water level behaviour are verified so the unit starts/stops correctly.

• Inspect fittings for leaks and run a short functional test: after tightening/part replacement, the unit is run to confirm no new leakage and stable output.

Common service parts in Kent RO (and when they usually need attention)

In most Kent RO complaints in Aurangabad, the root cause is one of these stages: the sediment pre-filter (protects the membrane), the pre-carbon and post-carbon filters (improve taste and odour), the RO membrane (main purification), and the control parts like SV and float valve (for correct operation). If the machine has UV or UF stage (depending on your model), the technician also checks that UV lamp running status and connections are correct, especially if water smells are persisting despite filter changes. Typical maintenance is not fixed for every home, but in many households: sediment pre-filters are changed roughly every 3-6 months, carbon filters roughly every 6-12 months, and the RO membrane often lasts about 2-3 years depending on inlet TDS, scaling, and usage hours.

How to decide whether repair is worth it (cost factors, time, and decision points)

The cost for Kent RO service in Aurangabad is decided by what the diagnosis finds: whether it is only a filter change, a membrane replacement, a booster pump/SMPS repair, or control part replacement like SV/float valve. Time also depends on access and the number of stages that need work, because a proper service includes inspection, part swap, and a functional test run. In most cases, it is worth repairing when the issue is limited to filters or one failing control/electrical part. If you have salty output plus repeated low rejection and the membrane shows clear aging/scaling, the technician will usually recommend membrane replacement rather than repeated minor adjustments.

When you should not wait and should call service immediately

• There is any leakage from the housing or under the purifier: stop using and call a technician to avoid water damage and short circuits.

• The unit keeps running continuously or does not auto shut-off: float valve/SV/control may be failing.

• RO output tastes salty/very different for more than 1-2 days: membrane or bypass can be involved.

• You hear repeated loud noise or the booster pump keeps struggling: running it like this can worsen damage.

• After heavy monsoon turbidity, if flow becomes very slow and taste worsens quickly: sediment filter clogging is likely and should be attended.

If you tell the service person your exact symptom (taste, smell, flow, noise, leakage, and whether it starts/stops normally), Water Purifier Care India (WPCI) can focus the checks faster and avoid unnecessary trial replacements. Next step: call for a Kent RO service visit in Aurangabad and keep the RO output TDS reading (if you have a TDS meter) and the last filter-change time ready for the technician.