Kent RO Service Dalmau @8506096743

If your Kent RO is acting up in Dalmau, you will usually notice it first in daily use: bad taste, salty water, slow filling, unusual noise, or even leakage under the unit. This is a diagnosis-first RO service page for Kent RO repair and servicing in Dalmau, so you can understand what the problem most likely is before a technician even opens the cabinet. At Water Purifier Care India (WPCI), we follow a fixed troubleshooting order to avoid repeat issues.

Start with symptoms: what they usually mean in a Kent RO

• Salty or metallic taste / high TDS on your TDS meter: commonly points to a tired RO membrane or membrane scaling, sometimes also a failing post-carbon stage.

• Water smells bad (musty/chemical) even when it is not salty: often means carbon filters are exhausted or there is chlorine/odour load from inlet water.

• Slow RO output or very low flow from the tap: usually a choked sediment pre-filter, low inlet pressure, or a weak booster pump.

• RO keeps running but stops producing water / no auto shut-off: can be related to pressure switch, float/level control, solenoid valve (SV), or membrane rejection issue.

• Water leakage from the housing or near fittings: typically a loose housing O-ring, cracked tubing, drain line leak, or a leaking membrane/pressurised joint.

• Strange noise, vibration, or frequent power trips: often due to air in lines, pump/SMPS issue, clogged flow path, or voltage fluctuation affecting the electronics.

What a technician checks on a Kent RO service visit (in order)

1. Check inlet water type and condition: borewell vs municipal supply, turbidity during monsoon, and whether the inlet is high TDS/hard water.

2. Inspect the pre-treatment: sediment pre-filter condition, flow rate, and whether the pre-carbon stage is overdue.

3. Measure system performance: inlet pressure, RO discharge/production flow, tank/line pressure behavior, and whether the unit reaches proper rejection.

4. Test controls: auto shut-off/float behavior, pressure switch, and solenoid valve (SV) operation during fill and drain.

5. Inspect for leaks and blockages: housing seals, tubing, drain line, and any scaling around membrane housing.

6. Finally, verify water quality: TDS reading before/after RO and a quick taste/smell check to confirm the final stages are working.

Common Kent RO parts and the typical causes behind failure

In Dalmau, the most common causes are not “mystery faults”. Hard water and high inlet TDS lead to faster sediment loading and membrane scaling. When pre-filters are not changed on time, the RO membrane works under higher pressure stress and starts letting more dissolved salts through. Carbon filters then exhaust and odours return. If the machine runs continuously, the technician also checks the shut-off path (float valve/level sensing and solenoid valve SV) because a control fault looks like a water problem.

Filter and stage replacement: what is usually due when symptoms appear

What decides the cost and whether repair is worth it

The service cost in Kent RO repair for Dalmau depends mainly on what the diagnosis finds: whether only filters are exhausted, whether the issue is control-related (auto shut-off/solenoid/pressure switch), or whether the RO membrane or booster pump needs replacement. Time also changes if the unit has heavy scaling or if there is a leak that needs line/tubing and seal work. Most of the time, a RO unit is worth repairing when only one stage has failed (pre-filters, carbon, or membrane) and the rest of the system is producing stable flow and acceptable TDS after service. If multiple stages are failing together, the technician will usually recommend a focused replacement plan rather than repeated partial fixes.

Before you call WPCI: quick checks you can do safely

• Check the inlet water: is the supply stable, or does pressure drop during the day or during monsoon?

• If you have a TDS meter, note RO output TDS after 10-15 minutes of running and also the inlet TDS if possible.

• Look for obvious leakage: wetness near the housing, under the storage tank, or drain line.

• Confirm whether the tank is filling: listen for water flow into the storage tank and check if the tap output stops correctly.

• Avoid repeated switching: if the membrane is scaled or control is failing, constant power cycling can worsen pressure behavior.

When it is not a DIY job (stop and call a technician)

Do not open the RO membrane housing, change wiring, or attempt to bypass solenoid valve (SV) or pressure switch yourself. If you have leakage from pressurised joints, you can flood the cabinet and damage electronics. Also, if the unit is producing salty water with high TDS, that usually requires membrane and stage verification—guesswork will waste time and water. WPCI technicians in Dalmau use the performance checks and control tests first, then decide exactly which stage needs replacement.

Next step: note your exact symptom (taste, smell, flow, auto shut-off, leakage) and whether you know inlet/RO TDS. Then book a Kent RO diagnosis service in Dalmau so the technician can check filters, controls, and membrane performance in the right order and fix only what is actually failing.