Kent RO Service Mohali @8506096743

If your Kent RO in Mohali is giving bad taste, bad smell, salty water, weak or slow flow, repeated low pressure, or you notice leakage, you do not need to guess. This Kent RO service in Mohali is for doorstep repair, service, installation, un-installation, and AMC support when the purifier starts failing in daily use. A technician typically checks the problem in a fixed order, because the same symptom can come from different parts.

Start with the symptoms: what they usually point to

• Bad taste or salty taste: often means the RO membrane is tired, or the system is bypassing RO due to a faulty solenoid valve (SV) / pressure issue.

• Bad smell (especially after storage): usually points to carbon filter exhaustion, stagnant water in the storage tank, or internal cleaning needed (post-carbon and tank hygiene matter).

• Slow filling / low water output: commonly due to choked sediment pre-filter, low inlet pressure from municipal line or borewell, or a failing booster pump (if your model uses one).

• Water leakage from the housing or under the unit: usually means loose fittings, worn O-rings, cracked housings, or a leak around the drain line.

• No water / RO not starting: often connected to inlet water flow, float valve stuck, electrical issue (SMPS / wiring), or UV lamp failure in UV-based stages.

• TDS reading not improving (high outlet TDS): points to RO membrane scaling, blocked pre-filters, weak pressure, or incorrect tank line routing after installation/service.

What the technician checks during a Kent RO service visit (in order)

• Verify inlet water availability and pressure (municipal vs borewell matters). Low pressure can mimic a membrane problem, so it is checked early.

• Check the pre-filters (sediment + carbon) for clogging, discoloration, and flow restriction.

• Inspect RO membrane performance by checking water output behaviour and whether the system is rejecting TDS properly (TDS meter readings help).

• Check solenoid valve (SV), float/level control, and storage tank lines to confirm the unit is not cycling incorrectly or mixing reject with product.

• Inspect electrical parts (SMPS, wiring connections, and UV lamp if present) and listen for unusual noise or vibration.

• Confirm leakage points and replace damaged O-rings/fittings after isolating the system.

Common causes in Mohali: hard water, scaling, and monsoon turbidity

Mohali supply can be hard, and many homes also use borewell water with higher sediment load. Hard water creates scaling on the RO membrane, which reduces rejection and makes outlet water taste salty or feel “not properly purified”. During monsoon, turbidity increases and pre-filters clog faster, leading to slow filling, frequent shut-off, and unstable production. If the purifier is installed near an overhead tank, incorrect inlet routing can also cause air or pressure fluctuations, which technicians correct during service.

Typical maintenance intervals for Kent RO parts (as a guide)

What decides the cost, how long it takes, and when repair is worth it

Service cost mainly depends on what failed: clogged filters need cleaning/replacement, while membrane replacement is a bigger part of the work. Labour time depends on access and the issue type, for example, correcting a leakage and changing O-rings is usually quicker than fixing low-pressure problems or correcting wrong line connections after installation. Whether the unit is worth repairing depends on the condition of the RO membrane, the quality of inlet water (TDS and scaling tendency), and whether electrical parts are still stable. Water Purifier Care India (WPCI) technicians in Mohali usually explain the diagnosis first—if the outlet TDS, flow, and cycling checks match membrane failure or valve/pressure failure, the repair plan becomes clear.

Before you call: quick checks you can do safely

• Check if inlet water is coming properly (no supply cut, no closed tap).

• Observe whether the purifier starts and stops repeatedly or stays idle.

• Look for visible leaks at the RO housing joints, drain line connection, and storage tank outlet.

• If you have a TDS meter, note inlet TDS and outlet TDS during production (do not test with the tank empty).

• If smell returns quickly after tank filling, do not keep using it for long—internal cleaning and carbon stage check is usually needed.

If you share what you are seeing—taste, smell, slow flow, leakage, noise, and whether inlet pressure is from borewell or municipal—then WPCI can guide the right service type for your Kent RO in Mohali. The sensible next step is to schedule a technician visit rather than changing parts randomly, because the symptom-to-part link is predictable when checked in the right order.