Kent RO Service Mokokchung @8506096743

If your Kent RO purifier in Mokokchung is giving trouble right now, you will usually notice it in taste, smell, flow, or even sound. Water Purifier Care India (WPCI) handles Kent RO service in Mokokchung with a diagnosis-first approach, so the first visit is focused on finding the actual fault, not just changing parts. Below is the same order our technician follows when you call for service.

What your symptoms usually mean in a Kent RO (and what we check first)

• Bad taste or salty water: we check RO membrane rejection, pre-filter/choking, and post-carbon performance (if carbon is exhausted, odour and taste carry over).

• Bad smell (musty/chemical) or discoloured water: we inspect carbon stage, check for stagnation in storage tank, and look for bypass/leakage in housings.

• Slow RO drinking water flow / low output: we test inlet water pressure (municipal vs borewell), measure booster pump condition, and check sediment/pre-filter clogging.

• Continuous running or auto shut-off not working: we inspect float valve and pressure switch/flow sensor logic, then check solenoid valve (SV) and electrical connections.

• No water from RO or frequent air lock: we check inlet taps/valves, confirm line blockage, inspect drain flow restriction, and check whether RO pump is drawing properly.

• Leakage near filter housings or under the unit: we look for housing cracks, loose O-rings, cracked tubing, and whether the unit is over-pressurised.

How a Kent RO service visit works in Mokokchung (step-by-step)

1. Quick checks at your tap: inlet supply source (borewell or municipal), water pressure feel, and whether the problem started after monsoon turbidity or a power fluctuation.

2. TDS and performance check: we compare your inlet TDS with RO output TDS using a TDS meter, then confirm whether the issue is pre-RO filtration or the RO membrane stage.

3. Filter stage inspection: we open sediment pre-filter and carbon stages, checking pressure drop and condition to decide whether replacement or cleaning is enough.

4. Membrane and internal plumbing check: we inspect RO membrane housing connections, flush/clean as needed, and verify flow path (including drain line condition).

5. Electrical and safety checks: for common Kent faults, we check booster pump, SMPS, UV/UF module (if present), and control components like float valve and solenoid valve (SV).

6. Final output test and explanation: we run the unit, confirm flow and shut-off behaviour, and tell you what changed and what to watch until next service.

Typical filter and UV/UF maintenance intervals (so you can spot neglect)

In Mokokchung, monsoon turbidity and hard water scaling can load the RO system faster than in cleaner areas. These intervals are typical, not guaranteed, and your actual requirement depends on inlet TDS and how many litres you use per day.

When repair is worth it (and when it is not a DIY job)

Most Kent RO issues are repairable, but some symptoms mean you should not keep running the unit. If you see leakage, burnt smell near electronics, repeated power trips, or RO output TDS staying high even after a full filter change, stop using and call for service. WPCI technicians usually find the root cause in one visit by checking inlet pressure, filter pressure drop, membrane rejection, and control components, instead of guessing.

What decides the cost and how long the work takes for Kent RO service in Mokokchung

Service cost depends on the fault type (filters vs RO membrane vs pump/electrical), how many stages need cleaning or replacement, and whether the issue is only performance or also includes leakage repair. Time depends on accessibility (under-sink vs wall-mount), the extent of clogging, and whether parts like membrane, carbon, booster pump, solenoid valve (SV), or UV/UF module need replacement. For most diagnosis + servicing jobs, the technician focuses on restoring correct flow and correct shut-off behaviour first, then confirms output quality before leaving.

Quick symptom checklist before you call WPCI

• Check if the inlet tap is fully open and whether neighbours face the same water pressure issue.

• Note your last service date (sediment pre-filter and carbon are the fastest to age).

• If you have a TDS meter, note inlet TDS and RO output TDS readings.

• Observe if the unit keeps running or stops normally after storage fills.

• If there is leakage, tell us the exact location: filter housing, drain line, storage tank area, or under the pump.

The sensible next step is to call for Kent RO service in Mokokchung with your symptoms and any TDS/output details you have. Once the technician checks inlet pressure, filter stages, membrane rejection, and control parts, you will get a clear fix plan instead of repeated trial-and-error.