
Repair
- Complete RO system inspection and diagnosis
- Repair of pump, SMPS, membrane and filters
Doorstep RO Repair, Installation & AMC in Solapur

Livpure Service Center Solapur always stands whenever you call for service. You must schedule a Livpure Service to experience it's satisfactory and low-cost service in Solapur. Livpure RO Service Solapur always care for your schedule with the vast service team.
Packages










If your Livpure RO is acting up in Solapur, you usually notice it first in daily water use: slow flow, bad taste or smell, frequent auto shut-off, leakage, or the unit not filling at all. These symptoms point to specific parts inside the RO, not random “general service”. A technician from Water Purifier Care India (WPCI) will usually diagnose in the same order: intake and pressure, then pre-filters and carbon, then RO membrane, then UV/UF and the control parts.
Low or slow water flow: technician checks inlet pressure, then sediment pre-filter choking (common in Solapur during monsoon dust and high turbidity), then carbon clogging, then drain flow restriction.
Water tastes salty or “metallic”: technician checks RO membrane performance (exhausted membrane usually after high TDS input), then verifies whether bypass/leakage is happening in housings.
Bad smell (often from carbon): technician checks pre-carbon/post-carbon condition and carbon media exhaustion, then checks for stagnant water in storage tank and pipe runs.
Auto shut-off / no output: technician checks float valve and storage tank level signal, then solenoid valve (SV) operation, then pressure switches/SMPS supply stability.
Leakage around filter housings or under the unit: technician checks O-rings, housing cracks, loose clamps, and checks whether membrane housing is leaking due to improper seating.
Noise or frequent on-off cycling: technician checks booster pump, air in lines, water hammer, and verifies correct drain line setup and flow rate.
Confirm the complaint and check output: technician tests whether RO is producing water and whether TDS improves from inlet to RO to storage.
Check intake first: verify inlet tap/borewell supply stability, check for low inlet pressure, and inspect inlet hose and valves.
Inspect and test filters: open the pre-filter housing and check sediment clogging; inspect carbon cartridges for exhaustion and proper flow direction.
Check RO membrane stage: measure reject/permeate behavior and inspect membrane housing for scaling or internal bypass; membrane replacement is decided only after performance checks.
Check UV/UF and sanitation parts (if present): verify lamp cartridge condition and water path; also check for water stagnation in tank and lines.
Check control and water path: test solenoid valve (SV), float/level sensor, storage tank fill cycle, and drain line connection so the RO cycle completes properly.
These timings are typical, not guaranteed. In Solapur, high hardness and high TDS from borewell or municipal supply can cause faster scaling on the RO membrane and faster clogging on pre-filters, especially when monsoon turbidity increases.
Stage in Livpure RO | Typical replacement / attention interval in many homes |
|---|---|
Sediment (pre) filter | Every 3-6 months (faster if water is very muddy) |
Carbon filters (pre/post carbon, if used) | Every 6-12 months (depends on taste/odor complaints) |
RO membrane | Usually 2-3 years (earlier in very high TDS without good pre-filtration) |
UV lamp (if UV model) | About 10-14 months of running time |
Storage tank hygiene (practical check) | Every service cycle if you notice smell or slow tank turnover |
Cost factors: what is failing (filters vs membrane vs pump/SMPS vs SV), how badly it is scaled or blocked, whether the unit needs major parts, and whether the service is a one-time repair or an AMC preventive schedule.
Time required: simple filter change and cleaning can be quick; membrane replacement and repeated testing take longer; electrical/control issues (SV, float, SMPS) require extra checks to confirm the cycle is stable.
Worth repairing: if the RO membrane is still passing good TDS and the fault is only pre-filters/carbon or a valve/sensor, repair is usually the sensible choice.
Worth replacing sooner: if the membrane is heavily scaled and frequent pre-filter clogging continues despite correct filter changes, performance will keep dropping and you may need earlier membrane work.
Not a DIY job: leaks from housings with O-ring seating, membrane installation, electrical parts, and UV/UF verification should be handled by a technician to avoid water contamination and damage.
Note the exact symptom: is it no water, slow flow, salty taste, bad smell, leakage, or noise?
Check if the problem started after monsoon, a water supply change, or a power fluctuation.
Look for visible leakage: near the filter housings, under the unit, or around the drain connection.
See whether the storage tank is filling: if tank stays empty, focus on float valve, SV, and pressure cycle.
If you have a TDS meter, record inlet TDS and RO outlet TDS (even one reading helps decide membrane health).
If you share these details, the Solapur service engineer can reach the correct fix faster. The next sensible step is to book a Livpure service visit right away and mention your exact symptom so WPCI can diagnose in the correct order instead of replacing parts blindly.
Why Trust Us?
in Solapur — Reliable, Fast & Professional
Technician visits your location for service
Guaranteed service visit in 48 hours for any request
Trained technicians for high quality service and repairs
Only high quality spare parts used for repairs
Watch
FAQ
Find answers to common questions about our services
Many people searching for a Livpure service center in Solapur simply want someone reliable to come home, find out why the purifier is misbehaving and fix it properly. That is what we do. We are not the brand's own service center, which we explain at the end of this page, but our technicians work on Livpure purifiers regularly and understand how they respond to Solapur's mix of corporation and borewell water.
Corporation water in Solapur comes mainly from Ujani dam on the Bhima, with Hipparga tank contributing, and reaches homes on an intermittent schedule. In between, many families use borewells or buy tanker water. Groundwater around Solapur is drawn from fractured basalt and is often hard, with high dissolved solids and, in many wells, nitrate above safe limits. A Livpure RO unit handles this well when it is healthy, but hardness steadily coats the membrane, and the extra cartridges that make Livpure distinctive have their own lifespans.
Mineraliser: adds calcium and magnesium back after RO so the water does not taste flat. Once spent, the water tastes bland again, even though the RO stage is fine.
Copper and zinc cartridges: some models, including copper-enriched Glo and Bolt variants, add small amounts of these metals. They have a fixed service life and are replaced with the filter set.
UF and UV stages: the UF membrane traps fine particles and the UV lamp disinfects. Both lose effectiveness gradually.
In-tank UV and smart indicators: on higher models and Smart subscription purifiers, indicators and connectivity track filter life. We service subscription units only where your plan allows outside servicing, so check your plan first.
Glo, Glo Star, Glo Pro, Bolt, Bolt Star, Pep Pro, Pep Plus, Envy, Zinger, Touch and older Livpure units. We also check Livpure Smart purifiers on request.
A frequent worry we hear in Solapur is about white marks on the purifier tap or a chalky film in the glass. People often assume the mineraliser is overdosing. In most homes it is actually the opposite problem: hard water bypassing the membrane through an over-opened TDS valve, or a membrane that has scaled and is letting more calcium through. We test before and after the membrane to find out which, and fix the cause instead of just changing cartridges.
| Problem | Possible Cause |
|---|---|
| Bland, flat-tasting water | Mineraliser cartridge exhausted |
| Chalky film in glasses | TDS valve set too open for hard borewell water |
| Slow fill, constant drain flow | Membrane scaling or faulty solenoid valve |
| UV indicator off or flashing | Lamp or ballast failure |
| Purifier silent with power on | Low inlet pressure or failed pump |
| Dripping from the base | Cracked housing or loose fitting |
With only corporation water, servicing every six months keeps a Livpure in good shape. Homes on borewell or regular tanker supply should plan on every three or four months. The best times to book are just before peak summer, when purifiers run hardest, and soon after the monsoon, when supply turns muddy for a while.
Every RO purifier sends part of its incoming water down the drain to carry away rejected salts. In a drought-prone district, that reject stream bothers people, and rightly so. A scaled membrane or a faulty flow restrictor can make a Livpure waste far more than it should. During a service we check the ratio of purified to reject water and correct it where a part has failed. We also suggest simple reuse: collect the reject water in a bucket for mopping floors, flushing toilets or washing the car. Reject water is too high in salts for drinking or for watering most plants regularly, but for cleaning it is perfectly useful, and in a Solapur summer every saved bucket counts.
Murarji Peth, Hotgi Road, Railway Lines, Saat Rasta, Navi Peth, Jule Solapur, Mangalwar Peth, Vijapur Road, Akkalkot Road, Datta Nagar, Dayanand College area, Sakhar Peth, Ashok Chowk, Majrewadi, Soregaon, Shelgi, Degaon and MIDC Akkalkot Road.
Although this page is titled around Livpure service center searches, Water Purifier Care India is an independent multi-brand provider. We are not Livpure Pvt. Ltd. and not its official or authorised service center. The Livpure name is used only to describe the purifiers we service. If your purifier is under manufacturer warranty or on an active subscription, you may prefer to contact Livpure directly.
Call 8506096743 or book online through this page to get your Livpure purifier serviced in Solapur.