Pureit Service Dehradun @8506096743

If your Pureit RO is giving trouble in Dehradun, you will usually notice it first in day-to-day symptoms: slow or no flow, salty taste, bad smell, strange noise, leakage, or repeated power issues. These symptoms often point to specific parts like pre-filters, carbon stages, RO membrane, UV/UF, pump, or inlet valves. Water Purifier Care India (WPCI) handles Pureit service in Dehradun with a diagnosis-first approach, so the technician checks the most likely causes in the right order before changing parts.

What your Pureit symptoms usually mean (and what the technician checks first)

• Slow flow or water not coming: technician checks inlet water pressure first, then sediment pre-filter choking (common in monsoon and borewell dust), then checks the booster pump/switching and RO membrane pressure drop.

• Salty taste or high TDS: technician checks RO membrane health and whether the post-carbon filter is exhausted; if bypass/low rejection is happening, the membrane is usually the cause.

• Bad smell (musty/chemical) or unpleasant taste: technician checks carbon filters and internal sanitization; if UV is present, UV lamp function is also checked.

• Water leakage around housing or under the unit: technician inspects housing seals, check valves, drain line connections, and whether the solenoid valve (SV) and fittings are leaking.

• No water after it starts (or it keeps restarting): technician checks electric supply stability, SMPS/transformer, float/level switch, and solenoid valve operation.

• Strange noise during filtration: technician checks pump running condition, air lock, clogged pre-filter, and any vibration/line blockage that makes the pump work under strain.

How a Pureit service visit is typically done in Dehradun

1. Ask what changed recently: after heavy rain, after using less water, after tank refilling, or after a power fluctuation.

2. Check inlet source and pressure: municipal vs borewell supply, overhead tank level, and whether the booster pump is needed.

3. Run a quick performance check: flow rate, reject/flush behaviour, and whether the unit is producing consistent output.

4. Inspect filters and internal stages: sediment pre-filter, pre-carbon and post-carbon filters, RO membrane condition, and UV/UF stage if present.

5. Test electrical components: pump, SMPS/transformer, solenoid valve (SV), and float/pressure switch signals.

6. Clean and reassemble: internal cleaning/sanitization if needed, then leak checks and a final function test before the unit is returned to use.

Common Pureit parts involved (and typical maintenance timing in hard-water areas)

In Dehradun, many homes have hard water and seasonal turbidity (especially around monsoon). That makes the sediment pre-filter fill faster and can strain the RO membrane. Typical timing depends on your input water TDS and how many litres you use daily, but technicians usually follow these practical windows for preventive maintenance.

What decides the service cost, how long it takes, and should you repair or replace?

Cost in a Pureit service is mainly decided by what the diagnosis finds. If it is a clogged sediment/carbon filter, it is simpler. If the issue is the RO membrane, pump, UV/UF module, solenoid valve (SV), or SMPS, the work becomes more involved. The time also depends on whether parts need replacement, whether the unit has leakage that requires seal/fitting work, and how much internal cleaning is needed. As for repair vs replace: if the membrane is exhausted or the unit is repeatedly failing electrical components, repairing may still be worth it, but the technician will compare the likely fixes needed in the next few months rather than guessing.

Before you call WPCI: 5 quick checks you can do safely

• Check if the overhead tank/borewell line has water and the float level is not stuck (no inlet water is a common cause of “no RO output”).

• Observe the flow: is it slow from the start or only after some minutes? Slow from start often means pre-filter pressure drop.

• Look for obvious leaks at joints, under the unit, and near drain connections; if water is pooling, switch off the unit and avoid running it.

• Check whether the power supply is stable; if the unit restarts or stops repeatedly, avoid trial-and-error with switches.

• If you have a TDS meter, compare raw water vs RO output TDS; a consistently high RO output with salty taste usually points to membrane or carbon stage failure.

When DIY is not a good idea

Do not open the RO housing if you are not sure about reconnecting lines and seals. Avoid cleaning with wrong chemicals, and do not remove the RO membrane casually. Electrical parts like SMPS/transformer, pump wiring, and solenoid valve (SV) connections need correct handling to prevent shock and repeated faults. If you suspect leakage or if the unit is not producing water at all, calling Water Purifier Care India (WPCI) for a proper diagnosis is the safer next step.

Tell the technician what you are seeing right now (slow flow, salty taste, smell, leakage, noise, or no water) and share roughly when it started. Then book a service visit so the technician can test inlet pressure, filters, RO membrane, and the electrical stages in order, instead of replacing parts blindly.