Pureit Service Tura @8506096743

If your Pureit RO in Tura is giving trouble right now, it is usually one of a few common faults: clogged pre-filters, exhausted carbon filters, a scaling RO membrane, low inlet pressure from borewell or municipal supply, or a failing pump/solenoid. Water Purifier Care India (WPCI) handles Pureit service in Tura by diagnosing symptoms first, then opening only the parts that actually need work.

What your symptoms usually mean (and what we check first)

• Bad taste or bad smell (especially after 1–2 months since last service): usually points to carbon filter exhaustion or poor post-carbon performance; technician checks filter housings, flow, and whether carbon is bypassing

• Slow water flow / low output: most often due to sediment build-up in the pre-filter or RO membrane scaling; technician checks inlet pressure, pre-filter differential clogging, and RO rejection/production ratio

• Water leaking from the housing or under the unit: commonly from loose fittings, cracked RO membrane housing O-rings, or a failing drain/flow restrictor; technician checks joints, seals, and runs a controlled leak test

• Unit makes noise but not enough water comes out: typically pump cavitation (low inlet pressure) or a failing pump/SMPS; technician checks inlet pressure, pump current draw, and electrical connections

• No water coming out / storage tank not filling: often related to float valve sticking, solenoid valve (SV) not opening, or a blocked line; technician checks float movement, SV operation, and line blockage

• Water is “salty” or TDS does not drop after RO: points to RO membrane exhaustion or a membrane fouling problem; technician checks TDS before/after RO and inspects membrane performance

What happens during a Pureit service visit in Tura (step-by-step)

1. Confirm the complaint: whether it is taste/smell, slow flow, leakage, no production, or tank not filling.

2. Check input water quality: we look at turbidity/particle load (monsoon impact is common in Tura), inlet pressure, and whether overhead-tank supply is stable.

3. Inspect filters and housings: sediment pre-filter and carbon stages are checked for clogging or channeling; we open only what is needed and clean/replace as required.

4. Test RO performance: TDS reading before and after RO, and basic production/rejection behaviour to confirm whether the issue is membrane-related.

5. Check the system parts that control water flow: storage tank float valve, solenoid valve (SV), and drain/flow restrictor operation.

6. Run a final flush and verify output: the unit is run for a short cycle to confirm stable flow, no leakage, and improved taste/quality.

Typical maintenance intervals for Pureit RO (so you can plan ahead)

When the problem is worth repairing vs when replacement is considered

Most Pureit RO faults are repairable because the issue is often the filter stages, RO membrane, or a controlled part like the solenoid valve, float valve, or pump. Repair is usually the right call when the storage tank, wiring, and major housings are intact and the RO problem matches filter/membrane condition. Replacement or major overhaul is considered when multiple critical parts fail together (for example, severe leakage with damaged housing and repeated membrane failure), or when the unit has been run with very dirty pre-filters for a long time, causing cascading fouling.

What decides the service cost and how long it takes

• Cost depends on the diagnosis result: whether it is only a pre-filter/carbon change, or RO membrane replacement, or pump/SMPS/UV/solenoid work

• Whether the issue is simple clogging or a performance problem (low TDS reduction) that needs membrane testing and replacement

• How many stages are involved in your model (some Pureit systems include UV or UF, so parts differ)

• Whether there is leakage that needs seal/O-ring replacement and careful housing inspection

• Time depends on access and condition: heavy scaling or blocked lines take longer than a routine filter swap

If you want the fastest fix, note what exactly is happening (taste, smell, slow flow, leakage, noise, or tank not filling) and since when. Then book a service visit with WPCI for a proper diagnosis in Tura, because the right repair depends on the symptom order, not guesswork.