RO Service Aurad @8506096743

If your RO water purifier in Aurad is giving trouble right now, you usually notice it before anything else: bad taste, bad smell, slow water flow, leakage, unusual noise, or the unit not starting. In this RO service page for Aurad, Water Purifier Care India (WPCI) focuses first on diagnosing the symptom, then checking the exact RO stage that most likely caused it. A correct diagnosis saves time and avoids unnecessary part changes.

Symptom-first diagnosis: what your RO problem usually points to

• Bad taste (especially after using for a while): commonly a exhausted RO membrane or carbon filter that can no longer remove odour and taste compounds

• Bad smell: often a dirty carbon filter, stagnant water in the storage tank, or bacterial growth due to delayed servicing

• Slow filling or low output: usually a choked sediment pre-filter, low inlet pressure (common with borewell and long overhead tank lines), or weak booster pump

• Water leakage from under the machine: usually a loose housing O-ring, cracked fitting, or leakage around the filter housings; sometimes a drain line issue

• Continuous running / auto shut-off not working: often a float valve/storage tank issue, solenoid valve (SV) fault, or membrane/control problem

• Not starting at all or frequent power trips: typically SMPS/PCB issue, dry-run due to low inlet water, or clogged inlet strainer/blocked line

What a technician checks during an RO service visit in Aurad

1. Check incoming water: inlet pressure, flow stability, and whether Aurad supply/borewell turbidity is spiking (monsoon can do this).

2. Inspect the pre-filters: confirm sediment pre-filter loading and carbon filter condition; check for bypass or incorrect installation.

3. Test RO output performance: check TDS reading (if available), reject/flush behaviour, and membrane rejection signs (high permeate TDS usually means membrane wear).

4. Check key parts safely: RO booster pump pressure, solenoid valve operation, storage tank float/level switch, and UV lamp status (if your model has UV).

5. Inspect for leaks and sanitation needs: check housing O-rings, fittings, drain line, and whether the tank and lines need proper cleaning.

Common RO filter and component issues (and why they happen)

Most RO problems in Aurad come from hard water and high TDS input, plus seasonal changes. Hard water causes scaling on the RO membrane surface; scaling reduces rejection and increases TDS in purified water, often leading to salty taste. If municipal supply or borewell water becomes more turbid during monsoon, the sediment pre-filter clogs faster and the unit starts giving slow flow or low output. Carbon filters mainly handle taste and odour, but they also get exhausted when water quality is poor for long periods or when the unit is not used regularly. If the storage tank is kept stagnant, smell can return even after filter replacement.

How often filters and membrane typically need service in hard-water areas

What decides the cost, how long it takes, and is repair worth it?

RO service cost in Aurad is mainly decided by what the diagnosis finds: whether it is a simple filter change, a leak that needs housing parts and O-rings, or a component repair like the booster pump, solenoid valve (SV), SMPS/PCB, float valve, or UV lamp. The time also depends on access and condition: a clogged pre-filter and basic cleaning can be quicker, while membrane replacement or internal component work takes longer. Repair is usually worth it when the issue is isolated (like filter exhaustion, a single valve fault, or a leakage at a fitting). It is less worth it when multiple major stages are exhausted at the same time, or when the RO membrane has failed and the system has been running with high TDS for a long period. WPCI checks performance first (including TDS and flow behaviour where possible) so you do not end up paying for the wrong parts.

When you should not DIY and what you can check before calling

• Do not open RO housings if you see active leakage; water can spray and damage the control board/electrical parts.

• Avoid bypassing filters “temporarily”; it usually increases membrane scaling and can worsen taste quickly.

• If the unit is not producing water, first check: inlet water availability, overhead tank water level, and whether the line is kinked or blocked.

• If output is slow, check whether other taps in the house are also low (this helps confirm low inlet pressure vs RO internal clogging).

• If taste/smell changed suddenly, note when it started and whether the unit was unused for days; this helps decide if sanitation or carbon replacement is needed.

If you share the symptom you are facing (taste, smell, slow flow, leakage, or not starting) and roughly when it began, WPCI can plan the correct diagnosis steps for your Aurad RO model. The sensible next step is to schedule a service visit now, because delayed servicing usually turns a small filter issue into a membrane problem.