Kent RO Service Katihar @8506096743

If your Kent RO in Katihar is giving issues right now, this is the usual pattern: one or two symptoms start first, then performance drops. Water Purifier Care India (WPCI) handles Kent RO service, repair, installation, and AMC support in Katihar, and we typically start by diagnosing what you are actually seeing or tasting. Below is what each symptom usually points to, and what a service technician checks in that same order.

Bad taste, bad smell, or salty water: what it usually means and what we check first

When RO water starts tasting salty, the RO membrane is the first suspect. If the taste is sour or the smell is unpleasant, the issue is more often from carbon stage ageing, bacterial growth due to infrequent cleaning, or contamination that reached internal lines. In Katihar, this becomes more common when input water quality changes during monsoon or when the overhead tank water sits for long periods.

• Check inlet water quality and TDS reading with a meter (if available) to see whether rejection is failing

• Inspect pre-filters (sediment) for clogging and carbon filters for exhaustion

• Test RO membrane performance by checking output quality after flushing

• Check UV/UF stage (if your model has it) for correct operation and lamp health

• Inspect storage tank, internal tubing, and check for stagnant water or leaks near fittings

Slow water flow or the RO takes too long to fill the storage tank

Slow flow is usually a pressure and blockage problem, not a “water is not coming” problem. Most cases come from clogged sediment pre-filter, exhausted carbon filter, or low inlet pressure from municipal supply/borewell. If you have a booster pump, weak pump performance or a faulty controller/relays can also slow filling.

• Verify inlet water is reaching the RO (no air lock, no closed tap, correct line connections)

• Check inlet pressure; low inlet pressure often needs a booster pump adjustment

• Inspect and replace clogged sediment pre-filter (common first step)

• Confirm carbon filter condition; heavy clogging reduces flow

• Check booster pump, solenoid valve (SV), and tubing for restriction if the RO keeps running but output stays low

Frequent leakage, water collecting near the housing, or wet floor

Leakage is not always a “pipe issue”. On Kent RO units, leaks can come from filter housings, O-rings, drain line fittings, or from the storage tank connector area. If leakage is happening while the RO is running, it can also point to a solenoid valve (SV) issue or a problem in how waste water is being routed.

• Locate the leak point: near pre-filter housings, near RO membrane housing, or near drain line joints

• Check and reseat O-rings and tighten housing caps correctly (wrong torque can cause leaks)

• Inspect storage tank valve/float valve connection for overflow or seepage

• Check drain line for cracks and correct routing (kinks can cause back pressure)

• If leakage is intermittent, test SV operation and check waste flow control

Machine runs continuously, water not stopping, or tank not filling properly

Continuous running or improper stop usually comes from control sensing or filling level problems. Common causes include float valve issues, float switch failure, weak water level sensing, or electrical control faults. In Katihar, this also happens when overhead tank water level fluctuates and the inlet keeps starving the RO.

• Inspect float valve and float switch movement in the storage tank

• Check power supply stability; voltage fluctuation can create repeated cycling

• Verify solenoid valve (SV) response and waste line control

• Confirm inlet supply consistency (borewell/municipal tank level drop)

• Check tubing for restrictions that can confuse the control system

How a Kent RO service visit in Katihar is usually done (what is covered, what is not)

1. You describe the symptom (taste, smell, slow flow, leakage, no water, continuous running).

2. Technician checks inlet supply and measures basic performance indicators (where possible).

3. Filters are inspected first: sediment pre-filter and carbon stages are cleaned/replaced if exhausted.

4. RO membrane and pressure-related parts are checked if output quality or rejection is failing.

5. UV/UF and storage tank components are inspected if your model has them and if smell/contamination is suspected.

6. Final checks: test output, confirm waste water control, and ensure no leakage after reassembly.

What decides the cost, how long it takes, and is repair worth it

The cost usually depends on which stage is failing: pre-filters, carbon stage, RO membrane, UV/UF, pump/SMPS/controller, solenoid valve (SV), or storage tank/float parts. The time taken depends on whether it is only servicing (cleaning + filter change) or requires membrane/pump or electrical replacement. In most cases, a failing RO membrane can be worth replacing if the rest of the system seals and fittings are healthy; if multiple components are worn together, the technician may suggest a more complete corrective service approach so you do not face repeat breakdowns soon.

How often Kent RO filters and membrane typically need replacement in hard-water areas like Katihar

If you tell me your exact symptom (taste/smell/slow/no water/leakage/continuous running) and whether your Kent RO is connected to municipal supply or borewell with an overhead tank, you can get the right diagnosis faster. For now, the sensible next step is to call WPCI for a service visit instead of guessing parts, because the checks above decide what needs replacement and what only needs cleaning.