Kent RO Service Mokama @8506096743

If your Kent RO in Mokama is giving trouble right now, it is usually not a “mystery problem”. Bad taste, slow water, bad smell, strange noise, leakage, or no output typically point to a specific stage of the system. Water Purifier Care India (WPCI) service technicians start by matching your symptom to the likely part, then confirm it with a few quick checks at your doorstep.

Symptom-first guide: what your Kent RO problem usually means

• Bad taste (metallic/salty) after filtering: often indicates RO membrane weakening or low reject, not just dirty filters

• Smell or stale water: usually a carbon filter issue or bio-growth from long storage / low flow usage

• Slow filling or thin output: common causes are clogged sediment/pre-filter, low inlet pressure from borewell/municipal supply, or a weak pump

• Strange noise while filtering: could be air in the line, pump wear, or a failing solenoid valve (SV) / check valve

• Water leakage from under the RO: usually a housing O-ring seal issue, loose fittings, or cracked components (technician must check safely)

• RO runs but no proper water output: often membrane fouling/scaling, low pressure, or a solenoid/float/auto shutoff problem

What a technician checks in Mokama (in the right order)

1. Check water source pressure and flow (borewell vs overhead tank): RO needs stable inlet pressure to reject salts

2. Inspect pre-filters and their condition: sediment pre-filter first, because it protects the carbon and membrane from fine dirt and rust

3. Check carbon stage and tubing/lines: confirm whether smell/taste issue matches carbon filter exhaustion and whether any bypass/leak exists

4. Test RO membrane performance: look for scaling due to hard/high TDS water and check if recovery is abnormal

5. Check valves and controls (SV, float valve/pressure switch where applicable): verify the unit is starting/stopping correctly and not stuck in a wrong cycle

6. Inspect for leakage and electrical health: housing seals, drain line connection, motor/pump sound, and whether voltage fluctuation affected SMPS

Common causes in Mokama: hard water, turbidity, and storage habits

Mokama supply conditions often change with seasons. During monsoon, turbidity and suspended dirt increase, so sediment pre-filters clog faster. If you use overhead storage tanks, water can sit longer; that can worsen stale smell and shorten the life of carbon filters. High TDS and hardness lead to scaling on the RO membrane, which shows up as salty taste, high TDS on output, and gradual flow reduction. If power supply is unstable, pump and SMPS performance may degrade over time, sometimes showing as noise or intermittent operation.

What you can check before calling for Kent RO service

• Check if the storage tank is full: if the tank is full, the RO may stop and you will feel like it is “not working”

• Look for obvious leaks at the quick-connect joints and under the filter housing (do not open when water is actively dripping)

• Note inlet water source: is the supply from municipal line stable or is borewell pressure fluctuating today?

• If output is slow, compare with last week: sudden change usually points to clogged pre-filter or a pressure drop

• If taste/smell changed after long non-use, ask whether the unit was idle for days; carbon can deteriorate faster with low flow usage

How often filters and membrane need replacement in hard-water areas

What decides the cost, how long it takes, and is repair worth it?

The cost depends mainly on what the diagnosis finds: whether it is a simple filter replacement, a clogged/failed RO membrane, a pump/SMPS issue, or a leakage/seal problem. Time also varies by the work scope. A pre-filter/carbon change with basic cleaning is usually quicker, while membrane replacement plus flushing and performance checks takes longer. Repair is usually worth it when the issue is limited to filters/valves and the membrane is still producing acceptable rejection; if the membrane is heavily scaled and output TDS stays high after cleaning, replacement becomes the sensible option.

When not to DIY: stop and call WPCI

• If you see leakage from the RO housing, stop opening parts unless you know the exact O-ring/housing layout

• If the unit makes loud noise repeatedly, do not run it continuously; pump damage can become permanent

• If output tastes salty and flow is low together, do not keep operating; membrane scaling may be progressing

• If there is an electrical smell, frequent tripping, or intermittent start, avoid opening the SMPS area

Next step: tell the technician your exact symptom (taste/smell/slow/no output/noise/leakage) and when it started, then allow a short inspection in Mokama. Once the stage is confirmed, the right repair or replacement can be done without guessing.