
Repair
- Complete RO system inspection and diagnosis
- Repair of pump, SMPS, membrane and filters
Doorstep RO Repair, Installation & AMC in Guntur

Livpure Service Center Guntur always stands whenever you call for service. You must schedule a Livpure Service to experience it's satisfactory and low-cost service in Guntur. Livpure RO Service Guntur always care for your schedule with the vast service team.
Packages










Your Livpure RO in Guntur is acting up, and you are probably seeing it every time you open the tap. Bad taste, salty water, slow filling, strange smell, leakage, or the machine running too much are the common signs. In most cases, the problem is not “mysterious” it is usually a clogged pre-filter, exhausted carbon, a failing RO membrane, low inlet pressure, or an electrical/control issue. Water Purifier Care India (WPCI) service technicians typically diagnose in a fixed order before they touch parts.
Salty or very high TDS taste: usually the RO membrane is exhausted or not rejecting properly, sometimes due to low pressure or a stuck/weak solenoid valve (SV).
Water smells bad (like chlorine/organic odour) even after purification: often carbon filter is spent, or there is microbial growth because filters were not changed on time.
Slow water flow / takes long to fill the storage tank: commonly sediment pre-filter is choked (hard water and monsoon turbidity in Guntur make this worse).
Frequent on-off, loud running noise, or no output: often related to pump/SMPS, air lock, or inlet pressure issues.
Leakage from the RO body/housing or wet fittings: usually a loose housing O-ring, cracked tubing, leaking drain fitting, or a worn valve connection.
No water at all / booster pump not starting: can be low inlet pressure, float/pressure switch issue, or electrical fault in the controller path.
A proper service for Livpure RO is not only “changing filters”. WPCI technicians start with quick checks that decide whether it is a filter problem, membrane problem, pressure problem, or an electrical/control problem. Then they open only what is necessary and verify results after each correction (especially TDS and flow).
Check inlet water condition: turbidity and basic inlet flow, because Guntur borewell/municipal mixing and monsoon dust can clog filters fast.
Check pressure and pump operation: listen for pump sound, check whether it is building pressure, and look for signs of weak booster pump or failing SMPS.
Check filter stages and flow path: inspect sediment pre-filter and carbon pre-filter for clogging and exhaustion; verify water is moving correctly through each stage.
Check RO membrane performance: measure TDS at inlet and RO output (using a TDS meter). If rejection is poor, the membrane is usually the culprit.
Check controls and storage: verify float valve/level control behavior and whether the unit is stopping/starting correctly; inspect solenoid valve (SV) function if applicable.
Check for leakage and sanitation: look at housing joints, tubing, and drain line; clean internal parts if required to remove scale and deposits.
Intervals are not fixed for every home because Guntur water quality varies by locality, borewell depth, overhead tank cleanliness, and how much the purifier is used. But typical guidance helps you understand what should be due. The biggest performance drops usually happen when sediment pre-filter clogs or when carbon and RO membrane exhaust together.
Stage | Typical replacement / attention interval |
|---|---|
Sediment (pre-filter) | Every 3-6 months (faster in monsoon or very turbid inlet) |
Pre-carbon / carbon filter | Every 6-12 months |
RO membrane | Usually 2-3 years (depends on inlet TDS, scaling, and pressure stability) |
UV lamp (if your Livpure has UV) | About 1 year of running time |
UF cartridge (if your model uses UF stage) | As per performance; often aligned with carbon/sediment schedule when fitted |
Check whether the inlet tap/borewell feed is stable. If inlet is low today, RO will underperform even if filters are fine.
Look for obvious leakage: under the RO body, around quick fittings, and near the drain line. If the area is wet, note where it is coming from.
Compare taste: is it salty immediately after a filter change, or did it gradually worsen over weeks? Gradual worsening points more to membrane/carbon exhaustion.
Observe flow time: is RO output very slow, or is it producing then stopping quickly? This helps separate filter clogging from control/float issues.
Check if power fluctuations are happening. If you notice frequent tripping or voltage dips, electrical parts may be stressed.
The cost decision usually depends on what the diagnosis finds. If only the sediment and carbon filters are clogged/exhausted, service is simpler. If the RO membrane needs replacement, the work becomes more involved because performance testing and proper installation are required. If there is leakage, technicians may need to replace O-rings, tubing, fittings, or correct housing sealing. For electrical issues like booster pump, SMPS, or solenoid valve (SV) faults, troubleshooting time and spare parts decide the final work scope.
In most practical cases, repairing an active Livpure RO is worth it when the cabinet is intact, the storage tank is working, and the issue is limited to one stage (filters, membrane, or one electrical component). If multiple stages fail together due to long neglect, the technician will usually recommend a more complete service because partial fixes may not restore stable TDS and flow.
If you see water leaking from the RO housing or fittings, do not keep running the unit. Sealing and pressure testing are needed.
If the unit makes abnormal noise or the booster pump runs continuously, electrical/control checks are required.
If taste/TDS is still bad after changing filters, the RO membrane and pressure rejection need testing.
If your model has UV/UF stages and you suspect failure, the system may need safe handling of the UV lamp and proper stage verification.
If you do not have a TDS meter, do not guess. Without measuring inlet vs RO output, you can replace parts repeatedly and still not solve the root cause.
Your next sensible step is to book a diagnosis service for your Livpure RO in Guntur and tell the technician exactly what you are noticing (taste, flow time, leakage spot, and whether it starts/stops normally). That single description helps them reach the correct fix faster and avoids unnecessary part changes.
Why Trust Us?
in Guntur — Reliable, Fast & Professional
Technician visits your location for service
Guaranteed service visit in 48 hours for any request
Trained technicians for high quality service and repairs
Only high quality spare parts used for repairs
Watch
FAQ
Find answers to common questions about our services
Many people type "Livpure service center Guntur" into a search bar when their purifier starts beeping or the water tastes off. To be clear from the start, we are not Livpure's own service centre. We are an independent, multi-brand service team that works on Livpure purifiers every week, comes to your home, and explains what your unit needs based on a proper water test.
Guntur is one of the hotter cities in coastal Andhra, with summer days touching the mid-40s °C. Most independent homes here receive municipal Krishna water from the Guntur Municipal Corporation, stored first in an underground sump and then lifted to an overhead tank. On the terrace, a black plastic tank in May can make the water feeding your purifier uncomfortably warm.
Warm feed water affects a Livpure in several ways. Bacteria multiply faster in the tank, so the UV and UF stages have more work to do. RO membranes pass slightly more dissolved solids when water is warmer, so output TDS can rise a little in summer. And the pump and adaptor run longer hours as families drink more, which brings forward electrical faults.
Add the fact that many households use borewell water during summer shortages, and that groundwater around Guntur is often salty and frequently high in nitrate, and you can see why the hot season is when most Livpure complaints arrive.
The Glo range (Glo, Glo Star, Glo Pro) is the most common, followed by the Bolt and Bolt Star, the budget Pep Pro and Pep Plus, and the Envy, Zinger and Touch models. We also see Livpure Smart subscription purifiers in rented flats and with students sharing accommodation. Some Smart plans include the company's own maintenance, so check your plan before calling an outside service.
The mineraliser, copper and zinc stages wear out quietly. The purifier keeps running, but the water loses the taste and benefit those stages were meant to add. We check their age on every visit.
| Issue | Most Likely Reason in Guntur |
|---|---|
| Output TDS higher in May than in December | Warmer feed water, borewell use, membrane ageing |
| Flat, tasteless water | Mineraliser cartridge used up |
| Bad smell from the tank | Warm stored water and overdue tank cleaning |
| Purifier cuts on and off | Low inlet pressure when sump level drops |
| Adaptor hot or dead | Long running hours and voltage swings |
| Leak from a fitting | Pipe hardened by heat, loose connector |
Shade or insulate the overhead tank if you can, or switch to a lighter-coloured tank when it is due for replacement. Clean the sump and overhead tank before April. Keep the purifier away from a window that gets afternoon sun and away from the stove. If you switch to borewell water during summer, let the technician know so the TDS adjuster can be tightened. These small steps reduce both breakdowns and the cost of replacement parts.
On municipal water alone, every six months suits most homes. On borewell or mixed water, every three to four months is safer, and the membrane should be checked each time. Mineraliser and copper cartridges follow their own litre ratings, which we record on every visit.
Families who keep a basic TDS meter at home can catch problems early. Test the purified water on the first of every month and note the number. A steady reading means the membrane is healthy; a reading that climbs by a noticeable margin over two or three months, or jumps suddenly after you start using the borewell, is the signal to book a visit before taste and safety suffer.
Brodipet, Kothapet, Pattabhipuram, Brindavan Gardens, Lakshmipuram, Arundelpet, Vidya Nagar, Syamala Nagar, Chandramouli Nagar, Ashok Nagar, Nallapadu, AT Agraharam, Gorantla, Amaravathi Road, Koritepadu, Etukuru Road, Inner Ring Road, Pedakakani and nearby areas.
Disclaimer: Water Purifier Care India is an independent multi-brand service provider. Despite the page name, we are not the Livpure service center and are not authorised by Livpure Pvt Ltd. The Livpure name is used only to describe the purifiers we service. If your purifier is under manufacturer warranty or a subscription plan, consider contacting Livpure first.
Call 8506096743 or book online for Livpure purifier service in Guntur.