
Repair
- Complete RO system inspection and diagnosis
- Repair of pump, SMPS, membrane and filters
Doorstep RO Repair, Installation & AMC in Vijayawada

Livpure Service Center Vijayawada always stands whenever you call for service. You must schedule a Livpure Service to experience it's satisfactory and low-cost service in Vijayawada. Livpure RO Service Vijayawada always care for your schedule with the vast service team.
Packages










If your Livpure RO is acting up in Vijayawada, you usually notice it first in the water and in the flow: salty taste, weak output, bad smell, noisy operation, leakage, or the RO not filling at all. These symptoms point to different parts of the system, so the right repair depends on the correct diagnosis. Water Purifier Care India (WPCI) focuses on checking the RO step-by-step, not guessing.
Bad or salty taste after purification: often a tired RO membrane, or bypass due to a failed check valve/low rejection
Slow or low water output: typically sediment pre-filter choking, carbon filter saturation, or low inlet pressure/booster issue
Water smells bad or looks discolored: usually pre-filters need replacement, or carbon filter is exhausted (common during monsoon turbidity)
RO keeps running but storage tank is not filling: likely solenoid valve (SV) problem, float valve issue, or inlet pressure/booster failure
Leakage from under the housing or around fittings: check for loose manifold connections, cracked housings/O-rings, or a leaking RO membrane housing
Purifier makes unusual noise or keeps tripping power: often pump wear, SMPS/relays issue, or voltage fluctuation stressing the electronics
Check inlet water: measure basic flow/pressure from municipal line or borewell and observe if there is heavy sand in monsoon
Inspect pre-filtration: examine sediment pre-filter condition first, then carbon pre-filter saturation (these protect the membrane)
Test RO performance: check TDS before and after RO using a TDS meter to confirm membrane rejection quality
Check controls: verify float valve operation and solenoid valve (SV) response so the unit stops/starts correctly
Inspect leaks and fittings: look at housing seals, tubing, and drain line for seepage under pressure
Check power and electronics (only when needed): listen to pump run pattern; test SMPS/relay symptoms if noise/tripping is reported
In Vijayawada, many homes use overhead tanks, and the inlet water can be hard with high TDS or carry sediment during rains. Hard water scaling can shorten membrane life, so pre-filter and carbon maintenance matters. Below are typical intervals; your actual timeline can be earlier if your inlet is dirtier or TDS is higher.
Stage / part | Typical interval (rough guide) |
|---|---|
Sediment pre-filter (pre RO) | Every 3–6 months |
Pre-carbon and post-carbon filters | Every 6–12 months |
RO membrane | Usually 2–3 years (depends on TDS and usage) |
UV lamp (if your model has UV) | About 1 year of running time |
UF cartridge (if present in the model) | As per usage and water quality; many homes need attention yearly |
Confirm water source: is borewell line running normally, and is overhead tank water level okay?
Check for obvious leakage: look for wet spots near filter housings, tubing joints, and the drain line area.
Observe flow: does the RO start and then slow down, or does it not start at all? Note this pattern.
Check TDS output (if you have a meter): compare with your earlier readings; a sudden jump usually indicates membrane/carbon failure.
If RO makes a constant buzzing or keeps running, note whether it stops on its own or never reaches storage tank fill.
Service cost depends mainly on which stage is failing (pre-filter/carbon vs RO membrane vs pump/SMPS vs control valves), how many parts need replacement, and whether there is additional work like deep cleaning or fixing leaks. The time also varies: a filter change with basic flushing is usually quick, while RO membrane testing, solenoid/float correction, and leak tracing take longer. Repair is usually worth it when the membrane is still doing its job (TDS rejection is acceptable) or when only controls/power parts are faulty. If the RO membrane and multiple filtration stages are exhausted together, the technician may recommend a combined replacement to restore performance reliably.
At Water Purifier Care India (WPCI), we align the repair with the symptom and the readings. A typical visit ends with confirming the RO output quality, checking that the unit stops correctly through the float control, and verifying there is no bypass or leakage at fittings. If your issue is related to voltage instability or repeated pump stress, we also guide you on the practical cause so the problem does not return quickly.
Next step: note your symptom (taste, smell, slow filling, noise, leakage, or no water), and book a Livpure service in Vijayawada so the engineer can test TDS and check the RO stages in order. That saves time and avoids repeated trial-and-error.
Why Trust Us?
in Vijayawada — Reliable, Fast & Professional
Technician visits your location for service
Guaranteed service visit in 48 hours for any request
Trained technicians for high quality service and repairs
Only high quality spare parts used for repairs
Watch
FAQ
Find answers to common questions about our services
When a Livpure purifier starts acting up, most people search for a Livpure service center in Vijayawada and call the first number they find. We are an independent multi-brand service provider, not the brand's own centre, and we make that clear below. What we offer is experienced technicians who understand Livpure purifiers, test your water before advising anything, and visit your home quickly.
Vijayawada is one of the hottest cities in Andhra Pradesh. In April and May, daytime temperatures commonly reach the mid-40s, and the rocky hills around the city radiate heat well into the night. Kitchens can get very warm, and purifiers mounted near stoves or west-facing windows run hot. Heat shortens the life of adaptors and pumps, and warm stored water is more hospitable to bacteria. Overhead tanks on terraces can heat up considerably by afternoon.
A few simple steps help a lot. Mount the purifier on a shaded wall with space for air. Keep the overhead tank covered and, if possible, shaded. Do not leave purified water sitting in bottles in the heat for long. And book a service just before the hot season so the UV lamp, adaptor and pump are in good shape.
Municipal supply in Vijayawada is treated Krishna river water from the Prakasam Barrage. In summer, when river inflows fall, supply can become irregular in some colonies, and families lean more heavily on borewells. Groundwater in the region has been found to be hard, high in TDS, and in some areas carries iron, manganese, nitrate and sulphate. Those conditions affect every stage of a Livpure: sediment filters stain and clog, membranes scale, and mineraliser cartridges can be coated by hardness.
Glo, Glo Star, Glo Pro, Bolt, Bolt Star, Pep Pro, Pep Plus, Envy, Zinger and Touch, along with Livpure Smart subscription purifiers. Most use a sediment filter, carbon filter, RO membrane and UV stage, with UF on many models, and finish with a mineraliser plus copper or zinc cartridges on some variants.
| Fault | Likely Reason |
|---|---|
| Purifier shuts off in the afternoon heat | Overheated adaptor or poor ventilation around the unit |
| Yellow or orange-stained pre-filter | Iron in borewell water |
| Output drops sharply in summer | Low inlet pressure plus a clogged pre-filter |
| Water tastes flat | Mineraliser exhausted |
| Faint metallic taste | Copper or zinc cartridge past its life |
| UV indicator off | Lamp failure or loose connector |
| Smart unit shows a filter-life warning | Scheduled replacement due |
For a home drinking only municipal water, a full service every six months is generally enough. For borewell water, plan every three to four months, since hardness and iron wear out filters fast. If your area relies on tankers during summer shortages, add a check soon after that period. Offices and shops where the purifier runs all day may need more frequent visits.
The membrane deserves special attention in this city. On hard borewell water, it can lose much of its salt rejection within a year, yet the water still looks perfectly clear. The only way to catch this is to compare the TDS of tap water with purified water. If the gap between the two is narrowing visit after visit, the membrane is wearing out. We record these readings on each service so you can see the trend for yourself and replace the membrane at the right time, neither too early nor too late. After the monsoon floods of recent years, we have also found several purifiers whose pre-filters were never changed after muddy water passed through them; if your area was affected, a full filter change is the safe course.
A few quick checks can save time. Make sure the inlet valve is fully open and that municipal or borewell water is actually reaching the purifier. Check that the plug is firmly in and the switch is on. If the unit displays an error code or warning light, note it or take a photo. And if water has been off for several days, run and discard the first tank after supply returns. If the problem continues, our technician will take it from there.
Benz Circle, Patamata, Auto Nagar, Kanuru, Penamaluru, Poranki, Ramavarappadu, Enikepadu, Gunadala, Machavaram, Labbipet, Governorpet, Suryaraopet, Gandhinagar, Bhavanipuram, Vidyadharapuram, Payakapuram, Nunna and Ibrahimpatnam.
Despite the page name, Water Purifier Care India is not the Livpure service center and is not owned, run or authorised by Livpure or its parent company. We are an independent provider servicing many brands, and Livpure is mentioned only to describe the purifiers we repair. If your purifier is under manufacturer warranty or a subscription plan that covers servicing, please contact the brand first.
Call 8506096743 or book online through this page for Livpure purifier service in Vijayawada.