Pureit Service Akola @8506096743

If your Pureit RO is giving trouble in Akola, you usually notice it first in the water taste, flow, or the machine itself. Maybe the outlet water is smelling bad, the RO is filling slowly, or you can see leaks around the housing. This page is for Pureit service and repair in Akola, where the technician starts with symptoms and checks the likely cause step by step, not guessing.

Symptom-first diagnosis: what your Pureit problem usually points to

• Bad taste (bitter/salty) or higher TDS on the outlet: often the RO membrane is exhausted, or a bypass/flow issue is happening after the membrane

• Bad smell (musty/chemical) even when water looks clear: usually pre-carbon or post-carbon filter needs replacement, or carbon is bypassing due to poor flow

• Slow RO start or slow filling: common causes are choked sediment/pre-filter, low inlet pressure (municipal supply fluctuations or borewell draw), or a weak booster pump

• Water coming out from taps but not enough pressure: check if RO is not producing, often due to clogged filters, low pressure, or solenoid valve (SV) not opening properly

• Continuous running, frequent cycling, or no shut-off: likely float valve/pressure switch issue, outlet tank level sensing problem, or solenoid/control fault

• Leakage from housing, tubing, or around the storage tank: can be cracked fittings, worn O-rings, loose clamps, or internal housing seepage after vibration/heat

What a technician checks in the right order during Pureit service in Akola

In Akola, input water quality can change with municipal supply timing and borewell usage, and monsoon months can bring more turbidity. So the service visit usually starts with the “easy to fail” parts first, then moves deeper only if needed. At WPCI, the technician follows a practical sequence so the root cause is identified, not just the visible symptom.

1. Check incoming water pressure and flow at the inlet. If pressure is low, the RO will not reject TDS properly.

2. Inspect and condition-check the pre-filters (sediment pre-filter and carbon). If they are clogged, everything slows down.

3. Measure outlet performance using a TDS meter (where possible) and compare against typical RO behavior. This helps confirm membrane health.

4. Check RO membrane-related flow path and look for bypass symptoms. Membrane exhaustion often shows as salty/bitter taste.

5. Inspect solenoid valve (SV) operation and internal connections. If SV timing is wrong, the RO cycles incorrectly.

6. Check storage tank level control (float valve) and drain line flow. Tank control faults cause continuous running or poor output.

Typical maintenance intervals in Akola (so you know what should have been serviced)

These intervals are typical for Indian conditions, not a strict warranty schedule. In Akola, hard water scaling and high sediment during seasonal changes can shorten filter life. If you are overdue, symptoms like bad taste, smell, or low production become more likely.

Before calling service: 6 quick checks you can do safely

• Check if the inlet tap valve is fully open and whether municipal/borewell supply pressure is normal today

• Look for obvious leaks around fittings, tank joints, and tubing; note where the water collects

• Observe production: does the RO start and stop normally, or keep running continuously?

• If you have a TDS meter, test inlet and outlet once (only water after some minutes of RO running, if your model has a storage tank)

• Check if the storage tank is getting filled. An empty tank often means production is failing or tank control is faulty

• Do not keep using the outlet water if it tastes very salty or smells strongly after a service gap. Call WPCI for diagnosis first

What decides the service cost, how long it takes, and when repair may not be worth it

Cost mainly depends on which stage is failing (filters vs RO membrane vs pump/SMPS vs UV/UF), and whether the issue is a simple blockage or an electrical/control fault. If the technician confirms a membrane or pump problem, it may require replacement rather than cleaning. Time also depends on access and part availability, plus whether multiple stages need attention (for example, clogged pre-filter plus membrane fatigue). In general, a Pureit unit is usually worth repairing when the fault is limited to consumables (filters/carbon/UV lamp) or a single component like SV, pump, or float valve. If repeated failures happen because the input water is very high TDS or frequent turbidity is not controlled, the technician may suggest a better maintenance schedule and correct filter sequence.

When it is not a DIY job (and you should stop trying)

• If there is leakage from inside the housing, do not open clamps or pressurised fittings without proper tools

• If the RO is sparking, tripping power, or the SMPS/pump makes unusual burnt smell or noise, stop and call immediately

• If the outlet is salty/bitter repeatedly after changing carbon, it usually indicates RO membrane exhaustion or bypass—needs proper testing

• If the unit runs continuously or does not drain properly, tank control (float valve) and SV timing need correct setup

If your Pureit in Akola is showing any of the symptoms above, the sensible next step is to schedule a diagnosis visit and tell the technician exactly what you noticed (taste, smell, flow, leakage, and whether the machine runs continuously). Water Purifier Care India (WPCI) can check the RO stages in the right order and fix the actual cause, not only the part that looks dirty.