Pureit Service Yawal @8506096743

If your Pureit RO water purifier in Yawal has started acting up, the quickest way to fix it is to match the symptom to the stage that failed. This is a diagnosis-first Pureit service page for Yawal, covering repair, installation, un-installation, and AMC support. When you call Water Purifier Care India (WPCI), the technician does not guess—he checks the most likely causes in order, starting from taste, smell, flow, and leaks.

Symptom to cause: what your Pureit problem usually points to

• Bad taste (often bitter or metallic) with normal water flow: usually the post-carbon filter is exhausted, or the RO membrane has started passing more TDS than it should.

• Water smell (musty, stale, or chlorine-like) after a few hours: usually carbon filter ageing, stagnant water in the storage tank, or a UV/UF issue depending on your model.

• Slow RO output or slow filling of the storage tank: usually a choked sediment pre-filter, low inlet pressure, or a failing booster pump.

• Water not coming at all or intermittent flow: usually electrical fault (SMPS/solenoid valve), low inlet pressure, or a stuck float/float valve.

• Leakage from under the machine or around the filter housing: usually loose fittings, cracked housing, O-rings needing replacement, or a leak at the drain line.

• Loud noise during RO running (humming, rattling, or sudden changes): usually air in line, failing pump/booster, clogged membrane, or a valve issue.

What the technician checks during a Pureit service visit in Yawal (in order)

1. Confirm the complaint with you: taste/smell, how long it has been happening, and whether municipal supply or borewell water is used.

2. Check inlet conditions: inlet pressure and whether the feed water is very turbid during monsoon (this affects pre-filter clogging).

3. Inspect and test the basic flow path: inlet → sediment pre-filter → RO membrane → storage tank outlet.

4. Measure performance indicators: using a TDS meter to compare feed vs RO output (high reject/low recovery usually means membrane or pressure issues).

5. Open housing only where needed: check filter seating, O-rings, and signs of leakage or bypass.

6. Verify key components: RO membrane condition, pre-carbon/post-carbon filters, solenoid valve (SV) operation, float/float valve, and pump/booster if the tank is not filling properly.

Which parts are typically serviced or replaced (and when)

In Yawal, hard water and seasonal turbidity are common. That is why pre-filters and carbon stages tend to wear faster than what people expect. A service technician usually focuses first on the stage that matches your symptom, then moves to the next likely failure so the problem does not return within weeks.

• Sediment pre-filter: typically every 3-6 months, faster if your incoming water is cloudy during monsoon.

• Pre-carbon and post-carbon filters: typically every 6-12 months to control taste, smell, and chlorine-related issues.

• RO membrane: usually 2-3 years depending on input TDS, scaling, and how often pre-filters were maintained.

• UV lamp (if your model has UV): typically around 1 year of running time; if water quality issues persist, the lamp and flow conditions are checked.

• UF cartridge (if applicable): checked during service; performance drops when the cartridge is exhausted or improperly maintained.

• Storage tank and tank outlet: checked for stagnant water and contamination, especially when smell returns after sitting.

What you can do before calling WPCI (simple checks only)

• Note the pattern: is it always bad, or only after the tank fills or after water sits for a few hours?

• Check if water is coming from the inlet line to the RO purifier (basic supply availability).

• If flow is slow, compare: is only RO output slow, or is your overhead tank fill also slow?

• If there is leakage, wipe the area dry and observe where it reappears (housing joint, drain line, or fitting).

• If you have a TDS meter at home, note feed TDS and RO output TDS readings (even one comparison helps the technician).

• Avoid running the RO continuously for long hours when you suspect a clogged pre-filter or low inlet pressure.

What decides the cost, how long it takes, and when repair is not worth it

The service cost mainly depends on what stage is failing: filters vs RO membrane vs pump/booster vs electrical parts like SMPS or solenoid valve. It also depends on whether the issue is a simple maintenance problem (like exhausted pre-carbon/post-carbon) or a performance problem caused by scaling, low inlet pressure, or repeated bypass. Repair time usually depends on parts availability and whether the unit has leakage that needs careful housing/O-ring work.

In general, repairing is worth it when the problem matches consumables (pre-filters/carbon) or when the membrane is still performing but needs cleaning or partial replacement. If the RO membrane is exhausted and multiple stages have also aged badly, technicians may suggest a focused replacement plan instead of repeated short repairs. A clear diagnosis with TDS reading and flow checks is what decides this on the spot.

Why Pureit problems return in Yawal if the root cause is missed

Many owners change only the filter they can see, but the underlying cause stays—like low inlet pressure, recurring high turbidity during monsoon, scaling on the membrane, or a pump/solenoid fault that stops proper RO cycling. WPCI technicians typically verify RO output with a TDS meter and check components like the float/float valve and SV so the system fills and runs correctly after the repair.

If you tell the service person your exact symptom (taste, smell, slow flow, noise, or leakage) and how long it has been happening, the diagnosis becomes faster. The sensible next step is to book a Pureit service visit for your Yawal home and let the technician check the RO stages in the correct order instead of guessing.