
Repair
- Complete RO system inspection and diagnosis
- Repair of pump, SMPS, membrane and filters
Doorstep RO Repair, Installation & AMC in Sangli Miraj Kupwad

Pureit RO service Sangli Miraj Kupwad always stands whenever you call for service. You must schedule a Pureit RO service to experience it's satisfactory and low-cost service in Sangli Miraj Kupwad. Pureit RO service always care for your schedule with the vast service team.
Packages










If your Pureit RO in Sangli, Miraj, or Kupwad is giving trouble right now, you do not need to guess for days. In most cases, the symptom you notice (salty taste, bad smell, slow water flow, leakage, loud noise, or no water) points to one or two parts that are failing. Water Purifier Care India (WPCI) technicians usually diagnose it in a fixed order, then service only the stage that is actually causing the problem.
If the water tastes salty or your TDS is much higher than before, the RO membrane may be exhausted or the membrane may be getting bypassed due to low pressure or a stuck solenoid valve (SV).
First check is the inlet water quality and pressure (borewell vs municipal supply changes the RO load). Low inlet pressure often reduces rejection and raises output TDS.
Then the technician checks pre-filters and carbon filters for choking (hard water and monsoon turbidity clog them faster).
Next is RO membrane performance and reject flow. If the reject line is not working properly, the RO will not separate salts.
Finally, they check storage tank and float/ball valve operation so water is not overfilled or stored incorrectly.
Slow flow is usually not “a small problem”. It is most often a blocked sediment pre-filter, a choked carbon filter, or insufficient pressure from the booster pump. In hard-water areas around Sangli and Kupwad, scaling can also reduce flow through the membrane. During service, the technician measures inlet pressure and checks whether the pump is running correctly. They also inspect the pre-carbon and post-carbon stages, and confirm whether the system is maintaining correct flow during RO operation.
If you see water leaking from the bottom or around fittings, treat it as an urgent issue. Leakage can come from loose tubing connections, a cracked housing, a worn RO membrane housing O-ring, or drainage line problems. WPCI technicians typically start with a quick visual trace while the RO is running, then stop the unit and check the exact leak point. They also verify if the drain (reject) line is blocked, because back-pressure can push water out from the housing.
When the RO does not dispense or keeps stopping, the issue is often control-related: float valve not triggering, solenoid valve (SV) sticking, or a problem in the water inlet path. If you have overhead tank supply, sometimes the inlet is low because the overhead tank level is low or the delivery line has air. During a service visit, the technician checks the float operation, SV function, inlet water availability, and whether the pump is receiving correct power. They also inspect pressure switch behavior and confirm the tank filling cycle is normal.
Noise is a clue. A new loud sound while filtering can be from the booster pump cavitating (low inlet pressure), a blocked flow path, or a fault in motor/SMPS electronics. Continuous running usually means the control side is not reaching the correct stop condition, commonly due to float/valve issues or a pressure/control mismatch. In case of abnormal noise or continuous running, switch off the unit and do not keep restarting again and again. Call for service so the technician can check pump suction, filters, and control components in one visit.
Diagnostic checks: inlet pressure and flow, outlet TDS if a TDS meter reading is available, and visual inspection of tubing, housing, and storage tank.
Filter stage inspection: sediment pre-filter, pre-carbon and post-carbon filters for clogging, discoloration, and bypass risk.
RO membrane check: signs of scaling, membrane rejection performance, and reject line flow behavior (to confirm whether salts are being separated).
UV/UF stage (if your model has it): UV lamp status and cartridge condition, checked as per the stage installed.
Final testing: system cycle check (fill, RO, reject, storage) to confirm the symptom is gone before the technician leaves.
The cost depends on which stage is failing (pre-filters, carbon filters, RO membrane, pump/SMPS, solenoid valve, tank controls), how bad the clogging or scaling is, and whether parts need replacement or only cleaning. Time also depends on access and the condition of the unit; a simple filter change can be quick, while membrane scaling or electrical faults take longer. Repair is usually worth it when the issue is limited to filters, a valve, or cleaning, and the rest of the system is performing. If the membrane is exhausted and the tank controls are also failing together, the technician will explain the combined option clearly so you can decide.
Stage (common in RO models) | Typical interval (not a guarantee) |
|---|---|
Sediment pre-filter | Every 3 to 6 months |
Carbon filters (pre/post) | Every 6 to 12 months |
RO membrane | Often 2 to 3 years, depending on inlet TDS and scaling |
UV lamp (if present) | About 1 year of running time |
UF cartridge (if present) | Varies with turbidity; replace when performance drops |
Check the inlet source: is borewell or municipal supply running normally, and is overhead tank level adequate?
Look for obvious leakage points around the bottom, tube joints, and drain line.
Note the symptom pattern: only slow filling, only high TDS, leakage while RO runs, or noise from start.
If you have a TDS meter, record inlet TDS and outlet TDS (even approximate readings help the technician).
Avoid repeated switching on if you hear loud noise or see active leakage; switch off and call WPCI for diagnosis.
If you tell your exact symptom (taste, smell, flow, leakage, noise, or no water) and the Pureit model, the technician can narrow the cause faster. The sensible next step is to schedule a service visit so the correct stage is tested and repaired, not guessed.
Why Trust Us?
in Sangli Miraj Kupwad — Reliable, Fast & Professional
Technician visits your location for service
Guaranteed service visit in 48 hours for any request
Trained technicians for high quality service and repairs
Only high quality spare parts used for repairs
Watch
FAQ
Find answers to common questions about our services
Gravity Pureit purifiers have a loyal following in southern Maharashtra. They need no electricity, they are easy to keep, and in a household drinking treated river water they do a sensible job. Sangli, Miraj and Kupwad, which get most of their piped water from the Krishna, are places where a gravity Pureit can be the right tool. But not for every home, and not in every season.
Our Pureit service in Sangli-Miraj-Kupwad starts by checking what water your Pureit is really treating, because that decides whether a simple kit change is enough or whether you need something more.
Gravity units (Classic, Advanced, Intella) pass water through a Germkill Kit with a microfibre mesh, carbon trap and germkill processor. They remove germs, dirt and some chemical impurities but do not reduce TDS. At the end of the kit's rated life, the purifier automatically shuts off water flow.
RO units (Vital Plus, Eco Water Saver, Copper+ Mineral, Marvella, Ultima) combine sediment and carbon filters, an RO membrane and UV, with some models adding copper or minerals afterwards. The Eco Water Saver range is designed to waste less water than older RO designs, which matters in a town where summer supply is rationed.
| Situation | Gravity Pureit | RO Pureit |
|---|---|---|
| Treated Krishna water all year | Generally suitable | Suitable |
| Municipal water with borewell use in summer | Not suitable for the borewell months | Recommended |
| Mainly borewell water | Not suitable | Recommended |
| Supply affected by flooding | Kit may clog; replace after flood | Change pre-filters and disinfect |
| Kupwad homes near industrial area on borewell | Not recommended | Recommended |
When the Koyna dam releases less water and the Krishna runs thin, the municipal corporation rations supply. Families who normally drink tap water start filling vessels from a borewell or buying tanker loads. Groundwater in this basalt area is frequently hard, and its quality varies from well to well. A gravity Pureit keeps working through this change, producing clear water, but it does not touch the dissolved salts. If your household makes this switch every summer, an RO model is the safer choice, or at least keep a separate supply of treated tap water for drinking during those weeks.
Many calls start with "my Pureit stopped." On gravity models, that is usually the automatic shut-off at the end of the kit. A new kit restores it immediately. Slow filtering on gravity units during the rains often means a mesh clogged with fine silt from turbid supply. On RO models, rising TDS in summer points to borewell scaling, while a non-stop motor usually means a stuck float or solenoid. After flood periods, we often see odour issues from filters that soaked up contaminated water.
Sangli residents remember 2019 and 2021, when the Krishna flooded large parts of the city. After any such event, replace the Germkill Kit or RO pre-filters, disinfect the storage tank, and run fresh water through before drinking. A kit that has filtered floodwater has done its work and should not be trusted further.
Germkill Kits last for the litres rated on the pack, which for an average family means a few months. On RO models fed by municipal water, sediment and carbon filters usually need changing every six months, sooner after the monsoon. Membranes can last up to two years on river water but much less on hard borewell water. UV lamps need replacing about once a year.
When buying a replacement Germkill Kit, match it to your exact model; kits for Classic, Advanced and Intella units differ, and a wrong fit can let water slip past. Keep the gravity unit on a stable shelf away from direct sunlight, and wash the transparent upper chamber with plain water rather than detergent, which can leave a taste behind.
Sangliwadi, Vishrambag, Vijaynagar, Gaonbhag, Khanbhag, Ganpati Peth, Hirabag, Shamrao Nagar, Wanlesswadi, 100 Feet Road, Madhavnagar, Budhgaon, Brahmanpuri, Miraj Station Road, Malgaon Road, Gandhi Chowk Miraj, Kupwad and Kupwad MIDC.
Water Purifier Care India is an independent multi-brand service provider and not the official or authorised Pureit service centre. The Pureit name is used only to describe the products we service. If your Pureit is still under manufacturer warranty, consider contacting the brand first.
Call 8506096743 or book through this page for Pureit service in Sangli, Miraj and Kupwad.