RO Service Bhokardan @8506096743

If your RO water purifier in Bhokardan is acting up right now, this is the quick diagnosis-first guide we use for RO service. Most issues show up as bad taste, salty water, slow flow, frequent draining, leakage, or the unit not starting. A technician from Water Purifier Care India (WPCI) will check the system in a practical order so the root cause is found, not just the symptom.

Common symptoms in Bhokardan and what they usually mean

• Bad taste or bad smell: often a carbon filter problem, stagnant water, or bacterial growth after a long shutdown

• Salty taste / very high TDS on the output: usually RO membrane exhaustion, or low RO rejection due to scaling and high inlet TDS

• Slow water flow / takes long to fill storage: common causes are choked sediment pre-filter, low inlet pressure (municipal/borewell variation), or a weak booster pump

• Water keeps draining or unit seems to waste water: often a stuck/failed solenoid valve (SV), membrane fouling, or an issue with permeate control

• Leakage from under the purifier or around the filter housing: typically loose housing O-rings, cracked fittings, or a leaking RO membrane housing joint

• No water production / power issue: could be SMPS failure, motor/booster failure, airlock, or float/level control not allowing the unit to run

What a technician checks during a Bhokardan RO service visit (in order)

1. Ask for the last maintenance done: pre-filter, carbon filter, RO membrane, UV/UF cartridge (if present), and when the taste/flow issue started.

2. Check inlet water condition: whether Bhokardan supply is muddy during monsoon, how hard the water is, and whether the inlet TDS is unusually high using a TDS meter.

3. Inspect pressure and flow: measure inlet pressure and confirm booster pump health if the unit uses a pump; low inlet pressure often mimics “membrane failure.”

4. Check the filter stages: remove and inspect sediment pre-filter, pre-carbon and post-carbon filters (as applicable), and look for clogging or channeling.

5. Check RO and control parts: inspect RO membrane output performance, test solenoid valve (SV) operation, and verify drain line function (to identify flushing/waste issues).

6. Check for leakage and electrical faults: check housing O-rings, fittings, and water path; then test power/SMPS and running current if the unit is not starting or keeps tripping.

Pre-checks you can do before calling for RO service

• Look for visible leaks: dry the area, run the unit for 5–10 minutes, and see exactly where water appears (housing seam, tubing joint, or membrane housing area).

• Check storage tank level: if the tank is full and the float/level control is stuck, the unit may stop or behave oddly.

• Note the exact change: did the issue start after heavy monsoon water, after a long shutdown, or after a previous filter change?

• Test with a simple TDS meter reading (if you have one): compare inlet and output TDS; high output with salty taste points to membrane/control issues.

• Observe the flow: is only RO output slow, or is inlet also slow? This helps separate pre-filter clogging from pressure problems.

Typical filter and membrane replacement timeline in hard-water areas

What decides the cost, how long the work takes, and is repair worth it?

RO service cost mainly depends on which stage is failing (sediment/carbon vs RO membrane vs electrical parts), how much internal cleaning is required (especially if scaling is present), and whether parts like the solenoid valve, booster pump, RO membrane, or O-rings need replacement. Time also depends on access and diagnosis difficulty: a simple filter change and cleaning can be quick, while membrane replacement plus line flushing and re-testing takes longer. Most of the time, repair is worth it when the unit is otherwise functioning and only one stage is exhausted. If multiple stages are failed at once (for example, membrane plus repeated carbon clogging), the technician will explain the trade-off clearly before proceeding, and WPCI follows that practical approach in Bhokardan.

When not to wait (and when DIY can make it worse)

• Call service immediately if you see leakage from the housing or tubing; repeated running can damage nearby electronics and fittings.

• Do not keep running if output water is salty with very high TDS; the membrane may be failing and the unit may also keep flushing waste.

• Avoid opening the RO housing without proper tools and clean handling; a damaged O-ring or misalignment can cause permanent leakage.

• If the unit keeps draining continuously or the drain line flow is abnormally high, the solenoid valve/control is likely involved—needs proper checking, not random part swapping.

• If the purifier is not starting, do not keep toggling power; get the electrical cause checked (SMPS/booster/faulty connections).

Next sensible step: tell the technician your exact symptom (taste, TDS, flow speed, leakage, or no production) and when it started, then ask for a stage-wise diagnosis. This helps you get the correct repair for your RO purifier in Bhokardan, instead of repeated trial-and-error.